Buy Watch Band Pin Remover with 3 Extra Pins

September 27, 2010 Sclark 5 comments

Watch Band Pin Remover with 3 Extra Pins

Spring Loaded Base for Easy Height Adjustment
Three Extra Replacable Pins
High Quality Finish as Seen in Picture
Easy To Operate
For all Kinds of Band with Push Pin Links

If your watch band needs adjusting, this is your tool! This handy tool will make shortening and adding links to your band a snap. This easy to use unit includes band remover and 3 extra pins 0.80 and 1.00mm. Tool adjust bands width up to size 21mm or 7/8 inches.

Rating: (out of 155 reviews)

List Price: $ 19.95

Price: $ 11.95

Find More Watch Band Pin Remover Products

Share and Enjoy:

No related posts.

Watch band, Extra, Pins, Remover, Watch

Comments

Leave a comment Trackback

Written by Ricardo Jacques about 2 years ago.

Review by Ricardo Jacques for Watch Band Pin Remover with 3 Extra Pins
Rating:
I purchased this item, because I have thin wrists and normally have to get all of my metal watch bands adjusted. This normally requires me to first locate a watch repair shop and then take my watch there for the links to be adjusted; normally at a cost of anywhere from $5 to $8. I finally decided to try the pin remover; not expecting anything special, however to my surprised it worked great! I had the links removed and the band resized in all of about 4 minutes, all without leaving the house. I would have given this 5 stars if there was a case to protect the device’s pin from getting bent by accident. However, that is minor, if you’re in the market for one of these pin removers you can’t go wrong here.
Written by Michael D. Bigham about 2 years ago.

Review by Michael D. Bigham for Watch Band Pin Remover with 3 Extra Pins
Rating:
The pin remover works great, but takes requires practice to use correctly. You have to line up the band in the cradle carefully and I broke a couple of pins learning the process. I contacted the seller, Watch Tools about buying some more pins. They offered to send me several replacement pins for free. You can’t beat that.
Written by E. M. Van Court about 2 years ago.

Review by E. M. Van Court for Watch Band Pin Remover with 3 Extra Pins
Rating:
The watch band pin remover works well, and is easy to use. Keep in mind that this tool only starts the pin removal, and you’ll need a pair of small pliers to complete the job (I use small, easily available chain nose pliers, about 110mm overall length). If you read the directions, you’ll be able to use this tool on the first try without breaking anything. Be aware that the pad that the bracelet rests on is spring loaded, but this is not a problem if you read the directions.

The only caveat is about watches, not the tool per se. Normally, a bracelets removable links are marked with an arrow to show the direction to push the pins out. Some Fossil watches are marked with two arrows… The pins friction fit in the middle rather than the end on the far side from where the tool’s pin engages the bracelet pin. The tool’s pin is a little short for these, but the small pliers make this a non-issue.

Read the directions, have the pliers, and this tool is great (Beware of Fossil watches).
Written by dennis wentraub about 2 years ago.

Review by dennis wentraub for Watch Band Pin Remover with 3 Extra Pins
Rating:
It was a small revelation when a jeweler showed me that friction pin fitted watch bands have directional arrows engraved inside the band links. Visibility is critical when aligning the vise pin with the friction pin that is being pushed through. This tool gives good visibility. Still, I recommend that you pick-up a jewelers’ loupe. If you are just slightly off center you may snap the vise pin. Happily this tool comes with three replacement pins. You’ll need two hands, so get a magnifying lens you can ‘hold’ in your eye socket. You’ll also want tweezers to hold the set screw that locks this tool’s push pin in place when you have to replace it. This screw is not much bigger than two grains of coarse salt! Buy an inexpensive set of jeweler screwdrivers to loosen the set screw for a damaged push pin. Needle nose pliers will help pull through the dislodged watch link pin. They may also be needed if you straighten a bent vise pin. Hint from one novice to another: when you replace the friction pin in your watch band after removing links, back it into the band the way it came through. The friction head of the pin is the first to come out and it should be the last to go back in. A small hammer will seal the deal. Adjusting a watch band can be quick, easy, and gratifying. This tool works!
Written by Richard D. Quillen about 2 years ago.

Review by Richard D. Quillen for Watch Band Pin Remover with 3 Extra Pins
Rating:
Product works well for its intended use. However, I must say you can use a small paperclip tip, held by a small pair of needlenose pliers, and accomplish the same thing FOR FREE. Just make sure you press DOWN in direction of arrows (pointing DOWN) Have watch resting on soft cloth or velvet if you have it, expect to exert some significant pressure, and when pin “gives” gently wiggle the links apart. Works for every watch I have ever owed.